تسجيل الدخول

مشاهدة النسخة كاملة : دريم بوكس 6500


M_salam63
2013/05/01, 01:15 AM
الاخوه الاعزاء
عندى دريم بوكس5600بدون لان هل ممكن اضافه كارت لان اليه
الرجاء الافاده ولكم جزيل الشكر

ashrafdishnono
2013/05/01, 02:33 AM
الاخوه الاعزاء
عندى دريم بوكس5600بدون لان هل ممكن اضافه كارت لان اليه
الرجاء الافاده ولكم جزيل الشكر

هذا الرسيفر ليس له
علاقة بأجهزة النت
رسيفر صيني
عادي جدا
ليس به
امكانيات تشغيل الشيرينج
أو فتح المشفر علي الاطلاق

تحياتي لك
يا غالي

patch_lov-

M_salam63
2013/05/02, 01:04 AM
استاذى العزيز الرسيفر ليس صينى وياخذ صوره الدريم وهو يساوى دريم 5620 لكن دريم 5620 به لان اما 5600 ليس به لان هل يمكن اضافه لان اليه
شاكر جدا

ashrafdishnono
2013/05/03, 09:20 PM
استاذى العزيز الرسيفر ليس صينى وياخذ صوره الدريم وهو يساوى دريم 5620 لكن دريم 5620 به لان اما 5600 ليس به لان هل يمكن اضافه لان اليه
شاكر جدا

لا يمكن اضافة أو تركيب
كارت لان للرسيفر
الذي ذكرته
لاْن بوردته مصممة بدون لان

تحياتي لك
أخي الحبيب

patch_lov-

ee_132
2013/05/04, 01:38 PM
عزيزى الجهاز ممتاز فى الشير ويفتح مايفتحه كافه اجهزه دريم من قنوات ويسطب عليه كافه الكامات لكن له صوره معينه لازم تشتغل عليها انجيما 1 جمينى 3.2 ومش اى صوره لان لها مواصفات خاصه وما يعيببه هو لزم يكون موصل بالكمبيوتر على طول طريقه عمله هو انك تعمل شير بينه وبين الكمبيوترعن طريق كوم او وصله التحديث العاديه وبعدين الكمبيوتر بيدا الاتصال ويبعت بيانات ******* الى الديم يعنى لازم يكون الدريم والكمبيرتر مفتوح والطريقه مطوله ولو عاوزها اطلبها اقولها لك

M_salam63
2013/05/04, 07:30 PM
عزيزى الجهاز ممتاز فى الشير ويفتح مايفتحه كافه اجهزه دريم من قنوات ويسطب عليه كافه الكامات لكن له صوره معينه لازم تشتغل عليها انجيما 1 جمينى 3.2 ومش اى صوره لان لها مواصفات خاصه وما يعيببه هو لزم يكون موصل بالكمبيوتر على طول طريقه عمله هو انك تعمل شير بينه وبين الكمبيوترعن طريق كوم او وصله التحديث العاديه وبعدين الكمبيوتر بيدا الاتصال ويبعت بيانات ******* الى الديم يعنى لازم يكون الدريم والكمبيرتر مفتوح والطريقه مطوله ولو عاوزها اطلبها اقولها لك

شكرا اخى العزيز ee132
ولو سمحت طريقه التوصيل باالكمبيوتر أكون شاكر جدا
الرجاء الاهتمام ضرورى
ولكم جزيل الشكر

ashrafdishnono
2013/05/05, 01:40 AM
عزيزى الجهاز ممتاز فى الشير ويفتح مايفتحه كافه اجهزه دريم من قنوات ويسطب عليه كافه الكامات لكن له صوره معينه لازم تشتغل عليها انجيما 1 جمينى 3.2 ومش اى صوره لان لها مواصفات خاصه وما يعيببه هو لزم يكون موصل بالكمبيوتر على طول طريقه عمله هو انك تعمل شير بينه وبين الكمبيوترعن طريق كوم او وصله التحديث العاديه وبعدين الكمبيوتر بيدا الاتصال ويبعت بيانات ******* الى الديم يعنى لازم يكون الدريم والكمبيرتر مفتوح والطريقه مطوله ولو عاوزها اطلبها اقولها لك

أخي الحبيب
أنا لا أعلم عن هذا الجهاز شيء
ومن قال لا فقد أفتي

تحياتي لك
يا غالي
patch_lov-

ee_132
2013/05/05, 01:32 PM
اولا يجب توصل الجهاز بكمبيوتر عن طريق كابل التحديث
2- تجهز الكمبيوتر لعمل الشير وطريقه فى الملف وانا معاك بسى تكون معايا فى كل خطوه عشان انا والله تعبت وكنت هرمى الجهاز والحمدلله ربنا سهل
انا بليل موجود انا شاء الله وحبت اجيبلك ملف حاول وعرفى النتيجه وحول تعمل ذى ما هو موجود بالظبط وبعدين قولى

M_salam63
2013/05/05, 01:47 PM
اولا يجب توصل الجهاز بكمبيوتر عن طريق كابل التحديث
2- تجهز الكمبيوتر لعمل الشير وطريقه فى الملف وانا معاك بسى تكون معايا فى كل خطوه عشان انا والله تعبت وكنت هرمى الجهاز والحمدلله ربنا سهل
انا بليل موجود انا شاء الله وحبت اجيبلك ملف حاول وعرفى النتيجه وحول تعمل ذى ما هو موجود بالظبط وبعدين قولى

معاك اخى الحبيب
لكن اين الملف
اعرف سيادتكم انى اعطيت الجهاز جمينى 3.2

ee_132
2013/05/05, 02:20 PM
Connecting Your Dreambox Via A Windows Gateway
These instructions are included as a courtesy of those users who, even at home, remain trapped in the Windows Matrix.
These instructions are based on material found at: http://bwinton.latte.ca/Palm/ppp.html. See that page for screen captures that may guide your setup. Note: that I found that it was best to assign an explicit pool of IP addresses rather than have Windows automatically allocate them. If I leave it to Windows to allocate them, Windows would tend to choose addresses that were already used on my network causing the PPP setup to fail. Also, make sure you reconfigure the maximum speed of the null modem you create to 115200 - you have to do this on the modem object, not on the connection object.
These steps will:
• modify a windows configuration file to allow Windows Remote Access Services (RAS) to detect incoming PPP connections
• create a modem definition for the null modem connection
• create an incoming connection definition for the PPP link
Modify %SystemRoot%\inf\mdmhayes.inf
These steps adds a line to a modem configuration file so that Windows can recognize an incoming PPP connection.
• Edit %SystemRoot%\inf\mdmhayes.inf - %SystemRoot% is usually c:\windows or c:\winnt
• Find the section [M2700Reg]
• Add the following line to the bottom of that section:
• HKR, Responses, "~", 1, 08, 00, 00, 00, 00, 00, 00,00,00,00 ; Server side - the client is requesting a connection
• Save the file
• Reboot windows. Note: I am almost certainly sure this reboot is mandatory.
Create The Null Modem
• open Start | Settings | Control Panel | Phone And Modem Options | Modems
• select Add...
• check Don't detect my modem, I will select it from the list.
• select Next
• select (Standard Modem Types) from the left hand list box
• select Communications cable between two computers from the right hand list box
• select Next
• select the COM port to which the Dreambox will be attached
• select Next
• accept the warning (if any) regarding the digitally signed driver
• select Finish
• select the modem definition just created
• select Properties
• modify the Maximum Port Speed to 115200
• select OK
Create The PPP Link
• open Start | Settings | Control Panel | Network And Dialup Connections
• select File | New Connection... from the Control Panel's menu bar
• select Next
• select Accept incoming connections
• check Communications cable between two computers
• select Next
• check Do not allow virtual private connections
• select Next
• do not check any users
• select Next
• select Internet Protocol (TCP/IP)
• select Properties
• check Allow callers to access my local network
• check Specify TCP/IP addresses
• enter a range of IP addresses that comply with the guidelines specified in the Linux configuration instructions above
It is probably best if you choose a range that is 2 addresses wide, so that the end address is always allocated to the dreambox.
• select Next
• select Finish
If the connection was successful, you should see a line with the following columns in your "Network And Dialup Connections" folder:
<Unauthenticated user> | Direct | Connected.
The IP address assigned to the dreambox will be evident by selecting "Status | Details" from the connection's context menu and then looking at the value of the "Client IP address" line.
If It Didn't Work!
If the connection doesn't seem to happen, you can try debugging it using the trace facilities described by this Micro$oft article (google: netsh ras ppp).
It may also be useful to inspect the null-modem's log by selecting the null-modem's definition object and selecting "View log" from its context menu. In the modem log, if you see a line like: "Recv: ~" followed by another which says: "Unknown Response" you almost certainly didn't do the mandatory reboot after editing mdmhayes.inf. Do it now :-)
First Steps
At this point you should have a working PPP connection. Under Linux this will be indicated by a foreground pppd process that hasn't yet terminated. In Windows, this will be indicated by the presence of a line in the "Network and Dialup Connections" folder as described above. If you don't have a working PPP connection you need try and work out why before continuing with the following steps.
These steps help you verify that the PPP connection really is working.
• use ping to verify connectivity with the dreambox's ip address. try pinging from a box other than the gateway box to verify that they gateway has been configured to forward ip traffic
• use ftp to connect to the ftp daemon on the dreambox's ip address (user=root, password=dreambox)
• use telnet to connect to the telnet daemon on the dreambox's ip address (user=root, password=dreambox).
Note: if it takes a while for the telnet login prompt to appear, there is probably an issue with name resolution on your network. If so, you may want to edit /var/etc/ppp/options on your dreambox to remove the usepeerdns option and manually add nameserver entries to /etc/ppp/resolv.conf on your dreambox.

ee_132
2013/05/05, 02:53 PM
اعتزر من سيادكم انا بكلمك من مكان العمل النت بطئ وانا عملت كوبى لها وان لم تفهم شئ انا معاك ماشى وعزرا انا سوف اكون موجود بليل
ثانيا النسخه لا زم تكون ان شاء الله جمنى مع 3.2 ppp connection* ان لم تتوافر سوف ارفقهالك بليل

ee_132
2013/05/05, 03:08 PM
وبالنسبه للا ستاذ ashrafdishnono تحياتي لك وشكر واجب

M_salam63
2013/05/05, 05:04 PM
اعتزر من سيادكم انا بكلمك من مكان العمل النت بطئ وانا عملت كوبى لها وان لم تفهم شئ انا معاك ماشى وعزرا انا سوف اكون موجود بليل
ثانيا النسخه لا زم تكون ان شاء الله جمنى مع 3.2 ppp connection* ان لم تتوافر سوف ارفقهالك بليل

شكرا أخى العزيز
الرجاء ارفاق النسخه
الرجاء التوضيح أكثر
ولسيادتكم جزيل الشكر على الاهتمام

ee_132
2013/05/05, 09:20 PM
النسخه http://www.4shared.com/account/home.jsp#dir=DsMjeDor

ee_132
2013/05/05, 09:36 PM
وبعدين بعد تحميل النسخه
خلاصه الكلام انت بتعدل ملف مجود فى الوندوز يتم اضافه سطر ميعين فى مكان معين
1- امتداد املف فى الوندوز موجود فى فولدر inf ومساره
C:\WINDOWS\inf
اسم الملف الى هتم التعديل فيه هو
mdmhayes.inf
اعمل بحث فى فولدر inf على الاسم mdmhayes.inf تمام دور فى الملف بالبحث طبعا على سطر
[M2700Reg] ; Null-Modem
فى اخر المجموعه دى هنضيف السطر ده
HKR, Responses, "~", 1, 08, 00, 00, 00, 00, 00, 00,00,00,00 ; Server side - the client is requesting a connection

وده صوره من الملف بعد التعديل

[M2700Reg] ; Null-Modem
HKR, Init, 1,, "None"
HKR, Init, 2,, "NoResponse"
HKR, Monitor, 1,, "None"
HKR, Answer, 1,, "CLIENTSERVER"
HKR, Answer, 2,, "NoResponse"
HKR, Settings, DialPrefix,, "CLIENT"
HKR,, Properties, 1, 00,00,00,00, 00,00,00,00, 00,00,00,00, 00,00,00,00, 00,00,00,00, 30,00,00,00, 00,c2,01,00, 00,c2,01,00
HKR, Responses, "CLIENT", 1, 08, 00, 00, 00, 00, 00, 00,00,00,00 ; Server side - the client is requesting a connection
HKR, Responses, "<h00>CLIENT", 1, 08, 00, 00, 00, 00, 00, 00,00,00,00 ; Server side - the client is requesting a connection
HKR, Responses, "CLIENTSERVER", 1, 02, 00, 00, 00, 00, 00, 00,00,00,00 ; Client side - the server has acknowledged and the connection is completed
HKR, Responses, "~", 1, 08, 00, 00, 00, 00, 00, 00,00,00,00 ; Server side - the client is requesting a connection


تمام خلص الخطوات دى بالظبط وبعدين اقولك الباقى هى صعبه اول مره وبعد كده تبقى تمام

ashrafdishnono
2013/05/09, 09:44 PM
شكرا لكل من تابع
الموضوع
وأفاد أخيه العضو
وتحياتي للجميع